Interior decoration frame house: options and materials

In this article we will deal with options for interior decoration of frame houses. Consider what materials are used for this, why some are used more often than others. We will tell about the stages of rough and fair finishing. And also consider the step by step instructions for the installation of some finishing materials. This article will be useful to those who decided to get by with a small capital investment on their own country plot and build a frame house.

What is a frame house

Purely structurally is a box assembled from lumber, sheathed on both sides with slab or sheet building materials, between which a heater is laid. The cladding material must meet certain requirements, where the main are strength, reliability, moisture resistance (if the rooms are wet) and good load bearing capacity.

It turns out that the internal surfaces of a frame house are practically no different from the same planes in an ordinary building, for example, built of brick. So, any finishing materials and designs can be used to make the rooms inside the frame house cozy and beautiful.

Draft finish

The finish of the walls of the frame house inside begins with installation on the frame plate or sheet materials. Usually plywood, chipboard, chipboard, drywall or gypsum-fiber boards are used for this. They are simply set to the frame of the house and fasten with screws.

There is nothing difficult in this operation. It is important to trim or adjust the plates (sheets) so that they are joined to the elements of the batten. Therefore, even at the design stage of a house, architects are trying to make this fit using frame elements. In this way, waste reduction is achieved by trimming the cladding sheets.

It is clear that from the inside such a covering of a frame house cannot be finished, therefore it is called roughing, that is, not final. The main task at this stage is to form the planes of the walls, which will be subsequently finished.

Finishing

So, let's proceed to the basic process - finishing. And let's start with the fact that we denote the general rules for conducting this type of work:

1. The process of finishing the interior rooms is carried out separately and not all at once. That is, they begin to repair one room, they finish it, move on to another.

2. The entire designated stage starts from the front door of the back room , gradually moving to the exit from the house.

3. First, communication networks are carried out, then they proceed to finishing works.

4. In each room, finishing is carried out in the direction from top to bottom . That is, first of all trim the ceiling, then the walls and at the very end of the floor base. There is an exception if it is decided to install a tensioning structure on the ceiling. Then they first finish the walls, then the floor, and only at the end stretch the ceiling.

Now we turn to the choice of materials and technologies for their installation or assembly.

On our website you can find contacts of construction companies that offer services construction of small architectural forms . Directly to communicate with representatives, you can visit the exhibition of houses "Low-rise Country".

Wallpapers

This material is the holder of the widest model range. And this is not only the design, but also variations on the method of manufacture and raw materials. Today, manufacturers offer several options with different bases:

• paper ;

• non-woven ;

• vinyl ;

• fiberglass ;

• acrylic ;

• fabric ;

• photo wallpaper ;

• exotic : cork, metallized, quartz and others.

What can be said about each of them. Paper models are rarely used today. They are thin, quickly fail. Practically do not maintain mechanical loadings. But the most important thing is that a very smooth surface is needed for paper wallpapers. Therefore, the rough finish of the frame house will have to bring to the maximum flatness, and this is the next cost.

In this regard, the other varieties are better. I especially want to mention vinyl-based coatings. They are thick, so that small flaws in the walls and small drops in the planes can be covered. They belong to the category of "washable", so that these wallpapers can be cleaned even with household appliances. Their disadvantage - support burning, emitting toxic smoke.

Flesilin wallpaper does not belong to the “washable” category.They are quite thin, but durable. The subtlety is their flaw. Because any dark stain on the wall will be well visible through them. Therefore, the walls in the frame house will have to be painted in a light solid color, if it is decided to use wallpaper of this type for finishing.

Tissue variations are not just fabric. This is a paper or non-woven base, which is glued to textiles. Such wallpaper under the action of even small loads are torn, well absorb moisture and odors, are a collection of dust. As for the advantages, it is necessary to distinguish their environmental friendliness.

Fiberglass wallpapers are the strongest on the market. But they are also the most difficult, therefore special glue is required for their sticking. Typically, wallpapers of this type are produced for painting, which is quite a serious plus, because it is possible to paint glass fiber wallpapers up to 15 times using paint of a different color.

It might be interesting! In the article the following link read about wall thickness of a frame house for year-round living: examples of calculation for different heaters .

I would like to mention two more types - it is quartz and liquid. The first is a non-woven fabric on which quartz (aka sand) of different colors is glued. The second is plaster, in which various decorative substances and materials are added. For example, glass beads, stone granules, metal or silk threads.

It should be noted that the wall covering technology has long been developed to the last detail. There are certain nuances for each model and type, but they are insignificant. Mostly wallpaper glue on special formulations that can be prepared or in the idea of ​​dry mixes.

Ceramic tile

As in any home, this material is used in wet areas: toilet, bathroom and kitchen. Sometimes it is laid on the floor in the hallway. Talking about tile can be long. Let us simply designate some of its advantages and disadvantages:

• high strength and wear resistance;

• huge variety textured front;

• large number of shapes and sizes;

• acceptable price .

These were pluses and several drawbacks:

• you can lay on the surface with good adhesion because the tile itself - the material is heavy;

• installation is not an easy process, so laying tile is trusted by professionals .

It might be interesting! In article on the following link read about the rules for carrying out insulation of a frame house outside under the siding + photo .

Wall paneling

For interior wall cladding of a frame house, wall paneling is one of the best options. By the way, it can be used instead of rough plating. That is, it can perform two functions at once: roughing and finishing. And this is doubly beneficial.

In the market, this material is represented by four varieties. So for the inner lining is better to use a variety of "Extra" and "A". For some office space suitable material and with a lower grade.

The only minus of wooden lining is the high fire situation that this material creates. Therefore, there is another variety on the market - plastic. True, this type of decoration is striking in its artificiality. Plus, he has lower heat and sound insulation qualities. But the price is lower.

With regard to installation, it is better to see once than hear a hundred times. Therefore, we propose to watch the video on this topic:

Flexible stone

New unique material that exactly repeats the texture of the stone. In fact, this is another wallpaper, which is based on fiberglass. And on it pasted colored sand or stone veneer. This type of lining received its name only because it imitates a stone, but is flexible in its body. So you can use it to revet walls with large differences, bends, bumps and hollows.

Decorative plaster

It should be noted that plaster, even in a frame house, in some cases is the right decision. Today, plaster mixtures are applied in thin layers, do not narrow the space of the rooms and serve as an excellent finishing material. Especially it is necessary to note textured and decorative plaster.

Firstly, this material perfectly hides the joints of plate and sheet materials used in roughing. Secondly, the walls lined with modern plaster mixtures are easy to clean, even with plenty of water. However, they do not get wet and do not peel off from the base. Thirdly, the plaster layer does not absorb smells and soot.

Other ways of finishing

There are actually a lot of options. Simply list those that are not included in the article above:

• decorative panels;

• panels from MDF ;

• plaster decorative tiles in the form of stone and other tile materials;

• tiles from stone , here you have to be careful and choose a thin material;

• stucco .

It can be interesting! In the article on the following link read about 9 options for exterior decoration of the frame house .

How to finish the ceiling surface

In principle, the finish of the ceiling in a frame house is no different from the finish in a brick or panel building. Here, as well as there, apply suspended, hemmed or stretch ceilings. In some cases, roughing may become the basis of roughing. For example, if drywall was used as a rough finish, it can be puttied well and then simply painted with water-based paint. Or stick a wallpaper on it.

Stretch structures look great in a frame house. It is important to maximize the alignment of the walls.

As for suspended models, there is a huge choice, ranging from drywall to rack-and-ceiling ceilings. Not bad in such houses will look even polystyrene tiles for painting. It is easily glued to any material, especially plaster or wood. The tile tears off small drops of the plane, the joints between the elements of the rough covering. If you choose the right paint, this type of finish will not absorb moisture, will not collect dust on its surface.

Generalization

So, what kind of generalization of finishing materials need to be made. In the frame house there are two types of finishing: the rough covering of the frame with plate or sheet materials and finishing, it is finishing. From the practice of construction, it can be concluded that today a large number of companies prefer OSB slabs as the best option for rough plating.

In fact, OSB has established itself as a durable, moisture-resistant material with a large bearing capacity. It is easily attached to the frame built with ordinary screws on the tree. Moreover, its surface has high adhesive properties. So you can trim the OSB with almost any material. In addition, oriented strand boards can be used for covering the ceiling and floor.

About the variety of finishing mentioned above. Just want to add - you should not convince yourself that the frame house is somehow different from the usual, at least brick. Here we are talking about interior decoration. Use any materials you choose or that the designer offers.

To see this, watch a video that shows the interior of a frame house:

It might be interesting! In the article on the following link read about gray in the decoration of the house: yes or no .

Conclusion on the topic

So, we dealt with the interior lining of the frame house (materials, options) and made a generalization on the topic, which indicated that there are no restrictions if there is a task of finishing the interior . That is, the choice is the master of the house.